IR-TEC America, Inc.

HRD‑600SP Series

Line Voltage SmartDIM Occupancy Sensor

The HRD‑600SP series of the TRANS‑PIR sensor family are two‑way IR remote programmable line voltage switching occupancy sensors with 0‑10V output for dimmable ballast or LED driver control. The sensor is capable of providing top‑notch energy efficient lighting control in multiple modes with fully programmable multi‑level high/low dim or SmartDIM continuous dimming control.

The HRD‑600SP series can be externally mounted with a lighting fixture via a 1/2" knockout hole. Like all TRANS‑PIR sensors, the HRD‑600SP series are available with interchangeable lenses.

 

 

  • Omni‑directional quad element infrared sensor
  • Digital data control ambient light sensor built-in
  • 2‑way IR remote programmable sensor setting
  • SmartDIM or multi-level high/low dim control
  • Remote programmable SmartDIM level setting
  • Up to 30 ft of remote programmable range
  • 347/480 VAC line voltage powered
  • Beeping or light flashing acknowledgement
  • IP‑66 rated external mounting design
  • Available with interchangeable lens options
    Models Tech ALS Power Output Setting Wiring Switching Control
    HRD‑600SP b PIR 347/480 VAC SLV+AO Remote Wire leads Zero‑cross Multi‑mode, multi‑level SmartDIM control
     b - lens code
LEGENDS:
PIR - Passive infrared     SLV - Switched line voltage     AO - Analog output (0‑10V)
Lens Options Code Coverage  
Standard
Cone
A
Extra Wide
Cone
B
High Bay
Cone
C
Standard
Flat Round
D
Extra Wide
Dome
F
Aisle Way
Arch
(Not for IP-66)
G
High Bay
Dome
H
 
 

The SRP‑280 is a universal two‑way remote programming device designed to provide easy configuration of the remote programmable TRANS sensors from IR-TEC. This handheld programmer not only allows uploading new setting commands to the sensor, but also downloading the current settings of the installed TRANS remote sensor from the floor via intuitive keypad operation. Up to 4 EZ-set modes can be stored and recalled for quick setting of multiple sensors with identical parameters. 

Please note that the TRANS sensors could have different appearances but with same settings, or same appearance with different settings available. Through successful download, the available settings of the installed sensor will be shown on the LCD with its current settings. Non-applicable settings will display as N/A. The SRP-280 can also be used as a remote controller to manually turn on/off of the lighting controlled by the TRANS remote sensor.

Features
  • Exceptionally long range 2‑way communication
  • Intuitive instructions enable easy programming
  • Upload and Download status acknowledgement
  • Easy to duplicate one sensor setting to another
  • Set SmartDIM level to deliver optimum lighting
  • Capable of reading the current dim output level
  • Set ambient light level for daylight harvesting
  • Set high/low dim level output for bi‑level control
  • EZ‑SET profiles enable setting multiple sensors
  • Various time settings for burn-in test and operation
  • Rubber jacket provides superb drop protection
Product Information
HRD-600SP Datasheet
HRD-600SP Installation Instruction
Lens Options Datasheet
Lens Installation Instruction
SRP-280 Datasheet
SRP-280 Operation Instruction

  • Omni‑directional quad element infrared sensor
  • Digital data control ambient light sensor built-in
  • 2‑way IR remote programmable sensor setting
  • SmartDIM or multi-level high/low dim control
  • Remote programmable SmartDIM level setting
  • Up to 30 ft of remote programmable range
  • 347/480 VAC line voltage powered
  • Beeping or light flashing acknowledgement
  • IP‑66 rated external mounting design
  • Available with interchangeable lens options

    Models Tech ALS Power Output Setting Wiring Switching Control
    HRD‑600SP b PIR 347/480 VAC SLV+AO Remote Wire leads Zero‑cross Multi‑mode, multi‑level SmartDIM control
     b - lens code
LEGENDS:
PIR - Passive infrared     SLV - Switched line voltage     AO - Analog output (0‑10V)

Lens Options Code Coverage  
Standard
Cone
A
Extra Wide
Cone
B
High Bay
Cone
C
Standard
Flat Round
D
Extra Wide
Dome
F
Aisle Way
Arch
(Not for IP-66)
G
High Bay
Dome
H
 
 

The SRP‑280 is a universal two‑way remote programming device designed to provide easy configuration of the remote programmable TRANS sensors from IR-TEC. This handheld programmer not only allows uploading new setting commands to the sensor, but also downloading the current settings of the installed TRANS remote sensor from the floor via intuitive keypad operation. Up to 4 EZ-set modes can be stored and recalled for quick setting of multiple sensors with identical parameters. 

Please note that the TRANS sensors could have different appearances but with same settings, or same appearance with different settings available. Through successful download, the available settings of the installed sensor will be shown on the LCD with its current settings. Non-applicable settings will display as N/A. The SRP-280 can also be used as a remote controller to manually turn on/off of the lighting controlled by the TRANS remote sensor.

Features
  • Exceptionally long range 2‑way communication
  • Intuitive instructions enable easy programming
  • Upload and Download status acknowledgement
  • Easy to duplicate one sensor setting to another
  • Set SmartDIM level to deliver optimum lighting
  • Capable of reading the current dim output level
  • Set ambient light level for daylight harvesting
  • Set high/low dim level output for bi‑level control
  • EZ‑SET profiles enable setting multiple sensors
  • Various time settings for burn-in test and operation
  • Rubber jacket provides superb drop protection

Product Information
HRD-600SP Datasheet
HRD-600SP Installation Instruction
Lens Options Datasheet
Lens Installation Instruction
SRP-280 Datasheet
SRP-280 Operation Instruction

Copyright ® IR-TEC America, Inc. All rights reserved.